| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to clear dirty flag on folio in error path
If node block is corrupted due to chksum mismatch or inconsistent
footer info, it needs to drop clear flag of node folio, in order
to persist inconsistent node data to storage. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: avoid force-completing uninitialized UVD rings
uvd_v7_0_sw_init() does not initialize the UVD decode ring for an
SR-IOV VF. However, amdgpu_uvd_resume() unconditionally force-completes
the decode ring when restoring its fence sequence.
Skip fence completion when the fence driver is not initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: bail out of setup if the controller is inaccessible
xhci_gen_setup() locates the operational registers using the capability
length read from the very first register:
xhci->op_regs = hcd->regs +
HC_LENGTH(readl(&xhci->cap_regs->hc_capbase));
If the controller is dead or has dropped off the bus, that read returns
~0, HC_LENGTH() truncates it to 0xff, and op_regs ends up 0xff bytes
past the page-aligned MMIO base, i.e. unaligned. The first access
through it, xhci_halt() -> xhci_handshake() reading op_regs->status, is
then an unaligned readl() on device memory. arm64 faults on unaligned
device accesses, so instead of xhci_handshake() catching the all-ones
value and returning -ENODEV, setup oopses:
xhci-pci-renesas 0005:08:00.0: Unable to change power state from D3cold to D0, device inaccessible
xhci-pci-renesas 0005:08:00.0: xHCI Host Controller
xhci-pci-renesas 0005:08:00.0: new USB bus registered, assigned bus number 1
Unable to handle kernel paging request at virtual address ffff80030a770103
ESR = 0x0000000096000021
FSC = 0x21: alignment fault
Internal error: Oops: 0000000096000021 [#1] SMP
pc : xhci_halt [xhci_hcd]
Call trace:
xhci_halt
xhci_gen_setup
xhci_pci_setup
usb_add_hcd
usb_hcd_pci_probe
xhci_pci_common_probe
xhci_pci_renesas_probe
This was hit with a Renesas uPD720201 that failed to power up ("Unable
to change power state from D3cold to D0, device inaccessible") yet still
reached the HCD probe path.
Read the capability register once, and if it reads back the all-ones
value (as xhci_handshake() and xhci_reset() already test for), abort
setup with -ENODEV before op_regs is derived from it. Reading it once
also avoids re-reading a register that may change under a concurrent
hot-removal. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mei: pass correct argument to function
The first argument to iwl_mei_write_cyclic_buf() should be the cldev
but the q_head pointer is passed instead. Fix it. |
| Improper initialization in an ASUS certain motherboard allows an physically proximate user to read or write arbitrary memory by inserting a specially crafted device. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_nat_sip: rewind offset when NAT shrinks the packet
sashiko says:
If map_addr() changes the packet length, such as when the public NAT IP
string is shorter or longer than the internal IP, coff will still point to
the offset relative to the pre-mangled packet.
If the packet shrinks, coff could overshoot the correct position,
potentially causing the next ct_sip_parse_header_uri() call to silently
skip bytes and miss subsequent Contact headers. Could this lead to a
failure to NAT those subsequent headers and leak internal network details? |
| Suricata is a network Intrusion Detection System, Intrusion Prevention System and Network Security Monitoring engine. From 8.0.0 until 8.0.6, the SMTP MIME parser in rust/src/mime/smtp.rs does not fully reset state when processing Content-Type: message/rfc822 encapsulation. An outer MIME part's encoding or filename state can leak into the inner message, allowing crafted mail to evade detections based on file.data, file.name, or extracted URLs when SMTP MIME decoding is enabled. This issue is fixed in version 8.0.6. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: zero-initialize stack-allocated cifs_open_info_data
Stack-allocated cifs_open_info_data may contain random data.
This can make some fields have wrong value if they are not set later. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: finish active block group cleanup if call_zone_finish() fails
do_zone_finish() clears BLOCK_GROUP_FLAG_ZONE_IS_ACTIVE before finishing
the zones. If call_zone_finish() then fails it returned early, leaving the
now inactive block group on fs_info->zone_active_bgs, leaking its
reference, the BTRFS_FS_NEED_ZONE_FINISH waiters are never woken, and as
its alloc_offset equals the zone capacity btrfs_zone_finish_one_bg() keeps
selecting it, spinning btrfs_zoned_activate_one_bg().
Fall through to the cleanup on failure too and return the error, but keep
the block group read-only as its zones are left inconsistent. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: initialize gigantic bootmem hugepage struct pages earlier
Gigantic bootmem HugeTLB pages are currently initialized from
hugetlb_init(), but page_alloc_init_late() runs earlier and walks
pageblocks to determine zone contiguity.
If a bootmem HugeTLB region is marked noinit, set_zone_contiguous() can
observe still-uninitialized struct pages through
__pageblock_pfn_to_page(). This may not trigger an immediate failure, but
it can make set_zone_contiguous() compute the wrong zone contiguity state.
If extra poisoned-page checks are added in this path, such as
PF_POISONED_CHECK() in page_zone_id(), it can also trigger an early boot
panic.
Initialize gigantic bootmem HugeTLB struct pages from
page_alloc_init_late(), before zone contiguity is evaluated, so later page
allocator setup only sees valid struct page state. This also makes the
initialization order more natural, as struct pages should be initialized
before later code inspects them. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: entry: Avoid unnecessary local_irq_disable() on kernel exit
Currently, when exiting to kernel mode, we attempt involuntary
preemption. The preemption logic expects IRQs to be disabled, which is
why we call local_irq_disable() before attempting preemption.
However, depending on the context, local_irq_disable() may be
unnecessary:
- __el1_irq(), the non-NMI EL1 IRQ path, already has IRQs disabled, so
local_irq_disable() is redundant.
- irqentry_exit_to_kernel_mode_preempt() immediately returns when
exiting from an NMI-like context, so calling local_irq_disable()
beforehand is unnecessary work.
Furthermore, it confuses the pNMI state tracking when we are in a
context with interrupts disabled and the GIC_PRIO_PSR_I_SET bit is set
in the PMR, leading to a warning when
CONFIG_ARM64_DEBUG_PRIORITY_MASKING=y:
WARNING: ./arch/arm64/include/asm/irqflags.h:63 at arm64_exit_to_kernel_mode+0xb8/0xc0, CPU#40: retsnoop/31805
CPU: 40 UID: 0 PID: 31805 Comm: retsnoop Not tainted 7.2.0-rc6-next-20260805 #7 PREEMPTLAZY
pstate: 234013c9 (nzCv DAIF +PAN -UAO +TCO +DIT +SSBS BTYPE=--)
pc : arm64_exit_to_kernel_mode (arch/arm64/kernel/entry-common.c:63)
lr : el1_abort (arch/arm64/kernel/entry-common.c:323)
pmr: 000000f0
Call trace:
arm64_exit_to_kernel_mode (arch/arm64/kernel/entry-common.c:63) (P)
el1_abort (arch/arm64/kernel/entry-common.c:323)
el1h_64_sync_handler (arch/arm64/kernel/entry-common.c:449)
el1h_64_sync (arch/arm64/kernel/entry.S:589)
[...]
Split arm64_exit_to_kernel_mode() into preempt, non-preempt, and
dispatch parts so that we can avoid this extra work where it is not
needed and avoid breaking the pNMI tracking logic. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: initialize DRC hash table before registering shrinker
shrinker_register() precedes the INIT_LIST_HEAD loop and the
drc_hashsize store. On weakly-ordered architectures (arm64, ppc),
a shrinker scan can observe drc_hashsize before the bucket list
heads are initialized, causing a NULL deref in the DRC shrinker
callback.
Move bucket initialization and the drc_hashsize store before
shrinker_register() so the hash table is fully initialized before
it becomes visible to the shrinker. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/madvise: skip device-private PMDs in cold and pageout walks
madvise_cold_or_pageout_pte_range() takes pmd_trans_huge_lock(), whose
pmd_is_huge() check returns true for a device-private PMD. The subsequent
!pmd_present() branch has a VM_BUG_ON() asserting migration is the only
allowed non-present case; a device-private PMD trips it.
Skip device-private PMDs in that non-present branch and continue to
huge_unlock before calling pmd_folio(). Downgrade the check to
VM_WARN_ON_ONCE() so an unexpected PMD softleaf logs a warning rather than
panicking. Drop the thp_migration_supported() guard: it expands to
IS_ENABLED(CONFIG_ARCH_SUPPORTS_PMD_SOFTLEAF), and both
pmd_is_migration_entry() and pmd_is_device_private_entry() already return
false when that config is not selected, so the guard suppresses only the
case where the warning would already be silent.
Potential trigger: an HMM-based GPU driver races with
madvise(MADV_COLD)/MADV_PAGEOUT: pmd_trans_huge(*pmd) reads true, then
migrate_vma_pages() flips the PMD to a device-private entry before the PMD
lock is acquired. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix response queue over-consumption in __qla_consume_iocb()
qla24xx_process_response_queue() advances ring_ptr past the head IOCB
before dispatching, so by the time __qla_consume_iocb() runs, ring_ptr
already points at the first continuation IOCB. The function however
looped purex->entry_count times starting at ring_ptr. As entry_count
includes the head, this consumed one entry too many: it stamped
RESPONSE_PROCESSED on the next, unrelated IOCB and advanced the ring
past it, silently dropping a legitimate firmware response. The head
IOCB's signature was also never marked.
Mark the head processed and account for it, then consume only the
entry_count - 1 continuation IOCBs, matching __qla_copy_purex_to_buffer(). |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: hibernate: mask DAIF before restoring hibernated kernel
The arm64 hibernate code manages the exception masking in an unsound
way, leading to potential crashes and/or warnings during resume.
When a hibernation image is saved in `swsusp_arch_suspend()`, all DAIF
exceptions are masked (by virtue of `local_daif_save()`), and the
suspended image is saved assuming that all DAIF exceptions will remain
masked when the image is restored.
When a hibernation image is resumed by `swsusp_arch_resume()`, only
interrupts are masked (by virtue of `local_irq_disable()` in
`resume_target_kernel()`). When pseudo-NMI is enabled the DAIF.IF bits
will be clear, and regardless of pseudo-NMI the DAIF.DA bits will be
clear.
This means that there are two problems:
(1) It is possible to take Debug, SError, or pseudo-NMI exceptions
during the resume process. This is unsafe, as during the resume
process both the old ane new kernels will tranisently be in an
inconsistent state, and swsusp_arch_suspend_exit() won't retain
an executable mapping of any exception vectors.
Any exception taken here will be fatal and silent.
(2) When re-entering the resumed kernel, some DAIF bits will be clear
unexpectedly. This permits Debug, SError, or pseudo-NMI exceptions
to be taken for a short period while the resumed kernel is not yet
in a consistent state.
This is detected by CONFIG_ARM64_DEBUG_PRIORITY_MASKING.
Avoid these issues by masking all DAIF exceptions during resume. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: media: tegra-video: fix of_node_put() on VIP parse errors
tegra_vip_channel_of_parse() initializes np from dev->of_node without
taking a reference, but its error paths drop one through the
err_node_put label. This underflows the refcount of the VIP device's
OF node when endpoint parsing fails on a malformed device tree.
The only reference the function takes on np is the success-path
of_node_get() stored in vip->chan.of_node, and that one is already
released by the tegra_vip_init() error path and by tegra_vip_exit().
Return errors directly instead of jumping to the bogus cleanup label. |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: move quota_init qc iterator increment
Move qc++ from the loop body into the for-loop increment
expression in gfs2_quota_init().
This keeps iterator progression explicit and avoids mixing pointer
advance with duplicate-slot handling in the loop body. |
| In the Linux kernel, the following vulnerability has been resolved:
block: handle nogenerate/noverify properly in fs-integrity
Check the BIP_CHECK flags before generating or verifying PI information,
otherwise this can be incorrectly called for non-PI metadata and
cause generation of incorrect metadata and crashed in the verification
handler.
The new behavior matches that of the block layer auto-generated
metadata. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/irq: Fix missing r2 clobber in PCREL inline assembly
In CONFIG_PPC_KERNEL_PCREL mode, r2 is no longer reserved for the TOC
pointer and is available as a caller-saved register [0].
Both call_do_irq() and call_do_softirq() use inline assembly to call
functions with stack switching, but fail to list r2 in their clobber
lists. This causes the compiler to assume r2 is preserved across these
calls, leading to register corruption when the called functions
(__do_irq and __do_softirq) clobber r2.
As a result of this kernel crash during interrupt handling is seen and
the kernel fails to boot:
BUG: Unable to handle kernel data access on write at 0xc000000404697638
Faulting instruction address: 0xc0000000000181ec
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000181ec] __do_IRQ+0x6c/0xc0
With older GCC, the compiler would conservatively allocate
callee-saved registers (like r31) for values spanning function calls,
accidentally avoiding the bug:
<__do_IRQ>:
00 00 00 60 nop
a6 02 08 7c mflr r0
f8 ff e1 fb std r31,-8(r1)
f0 ff c1 fb std r30,-16(r1)
2d 03 10 06 pla r31,53297316
...
3d e8 ff 4b bl c0000000000165ac <__do_irq>
00 00 21 e8 ld r1,0(r1)
28 00 4d e9 ld r10,40(r13)
40 00 21 38 addi r1,r1,64
2a f9 aa 7f stdx r29,r10,r31
With newer GCC 14, the compiler uses r2 for such values, exposing the
missing clobber specification:
<__do_IRQ>:
00 00 00 60 nop
a6 02 08 7c mflr r0
f0 ff c1 fb std r30,-16(r1)
f8 ff e1 fb std r31,-8(r1)
29 02 10 06 pla r2,36252592 # c0000000022aadc0 <__irq_regs>
...
85 dc ff 4b bl c000000000015ee0 <__do_irq>
00 00 21 e8 ld r1,0(r1)
28 00 2d e9 ld r9,40(r13)
30 00 21 38 addi r1,r1,48
2a 11 c9 7f stdx r30,r9,r2
Fix this by adding r2 to the clobber list for both call_do_irq() and
call_do_softirq() when CONFIG_PPC_KERNEL_PCREL is enabled.
[0]: https://www.mail-archive.com/gcc-patches@gcc.gnu.org/msg313226.html |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: policy_int make sure list heads are initialized before fail path
If profile create fails before policy_init is complete the list heads
are not properly initialized causing profile_free() sanity checks to
trigger the following splat.
AppArmor WARN aa_policy_destroy: (((!list_empty(&policy->profiles) && (&policy->profiles)->prev != ((void *) 0x122 + (0xdead000000000000UL))))):
WARNING: security/apparmor/lib.c:509 at aa_policy_destroy+0x164/0x1b0 security/apparmor/lib.c:509, CPU#0: syz.0.17/5541
Modules linked in:
CPU: 0 UID: 0 PID: 5541 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:aa_policy_destroy+0x16b/0x1b0 security/apparmor/lib.c:509
Code: 85 ed 7e 4d e8 96 bc 37 fd 5b 41 5c 41 5e 41 5f 5d e9 19 27 4e 07 cc e8 83 bc 37 fd 48 8d 3d 0c f0 d3 0b 48 c7 c6 a4 eb 38 8e <67> 48 0f b9 3a e9 04 ff ff ff e8 66 bc 37 fd 48 8d 3d ff ef d3 0b
RSP: 0018:ffffc9000345eaa0 EFLAGS: 00010293
RAX: ffffffff848f530d RBX: ffff88803f734800 RCX: ffff88801af2a580
RDX: 0000000000000000 RSI: ffffffff8e38eba4 RDI: ffffffff90634320
RBP: 0000000000000000 R08: 0000000000000cc0 R09: 00000000ffffffff
R10: dffffc0000000000 R11: fffffbfff1d95913 R12: dead000000000122
R13: ffff88803f734800 R14: ffff88803f734828 R15: dffffc0000000000
FS: 00007f5f6a1836c0(0000) GS:ffff88808c519000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055d02407b048 CR3: 0000000012aa9000 CR4: 0000000000352ef0
Call Trace:
<TASK>
aa_free_profile+0x9d/0x9f0 security/apparmor/policy.c:334
aa_alloc_profile+0x1e4/0x3e0 security/apparmor/policy.c:416
unpack_profile security/apparmor/policy_unpack.c:1153 [inline]
aa_unpack+0x17db/0x7430 security/apparmor/policy_unpack.c:1748
aa_replace_profiles+0x226/0x2a20 security/apparmor/policy.c:1183
policy_update+0x234/0x4a0 security/apparmor/apparmorfs.c:505
profile_load+0x1cb/0x320 security/apparmor/apparmorfs.c:522
vfs_write+0x296/0xba0 fs/read_write.c:685
ksys_write+0x150/0x270 fs/read_write.c:739
do_syscall_x64 arch/x86/entry/syscall_64.c:61 [inline]
do_syscall_64+0x166/0x520 arch/x86/entry/syscall_64.c:84
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f5f6939e0d9
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f5f6a183028 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007f5f69625fa0 RCX: 00007f5f6939e0d9
RDX: 0000000000000041 RSI: 0000200000000400 RDI: 0000000000000003
RBP: 00007f5f6a183090 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000001
R13: 00007f5f69626038 R14: 00007f5f69625fa0 R15: 00007ffe23725c18 |
