| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/9p/usbg: remove bogus context initialization in alloc_requests
alloc_requests() initializes usb9pfs->in_req->context to point at the
struct f_usb9pfs instance itself. usb9pfs_queue_tx() later overwrites
this with the real struct p9_req_t pointer before every transmit, and
usb9pfs_tx_complete() clears it back to NULL after each completion, so
in_req->context only ever holds a valid p9_req_t once a request has
actually been queued.
usb9pfs_clear_tx(), however, can run at any time (mount close, gadget
disable) independent of whether a request was ever queued. If it runs
before the first usb9pfs_transmit(), it reads the leftover sentinel
value, type-confuses the struct f_usb9pfs pointer as a struct
p9_req_t, and both writes through it (req->t_err = -ECONNRESET) and
hands it to p9_client_cb(), which manipulates req->wq and req->refcount
at bogus offsets inside f_usb9pfs. This reliably corrupts memory or
panics whenever the transport is torn down before any 9p request has
been transmitted, e.g. mounting and immediately unmounting, or a cable
disconnect racing the very first request.
usb9pfs->out_req->context is set the same way but is never read by
this transport (usb9pfs_rx_complete() identifies the instance via
ep->driver_data instead), so it serves no purpose either.
Both endpoints' ->driver_data are already set to usb9pfs in
enable_endpoint(), which is what the completion handlers actually use
to recover the f_usb9pfs instance. Just drop the leftover
->context assignments; usb_ep_alloc_request()/alloc_ep_req() already
return zeroed requests, so in_req->context correctly starts out NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net/9p/usbg: clear stale client pointer on close
p9_usbg_close() tears down the client transport, but usb9pfs keeps
using usb9pfs->client from asynchronous TX and RX completion handlers.
A late completion can therefore dereference a client that has already
been freed during mount teardown.
Clear usb9pfs->client under usb9pfs->lock when closing the transport,
detach any pending TX request from in_req->context, and make the TX/RX
completion handlers bail out once the transport has been detached. This
keeps late completions from touching a freed or rebound p9_client. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: interface: validate the IP header on xmit
Packets injected into an xfrm interface (e.g. AF_PACKET on an xfrmi
device) reach the xfrm output path without IP header validation, but
xfrm4_transport_output() uses iph->ihl for __skb_pull() and memmove()
and expects the header to be valid.
vti_tunnel_xmit() already calls pskb_inet_may_pull() before handing
packets to the xfrm output path. Do the same in xfrmi_xmit() and
perform the header checks ip_rcv_core()/ip6_rcv_core() do on entry
to the IP stack: reject wrong IP versions and malformed IPv4 header
lengths. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: espintcp: reorder operations within espintcp_init_sk
When enabled on a socket, espintcp sets the socket callbacks to its
own before it has finished setting up its context and published it as
icsk_ulp_data. Any one of those callbacks that gets called before will
dereference a NULL icsk_ulp_data.
Fix this by reording the operations, and add memory barriers to ensure
callers will have a struct espintcp_ctx available. Add a few
WRITE_ONCE/READ_ONCE too while we're there. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/drm_crtc: ensure dma_fence_ops remain valid during device unbind
In [1], sashiko reported the following issue:
=== snip ===
Looking at how these fences are managed, drm_crtc_create_fence()
creates a dma_fence without taking a reference to the drm_device or
drm_crtc. Because the sync_file framework exposes this fence to
userspace, the fence can outlive the CRTC.
The dma_fence contract requires that data accessed by dma_fence_ops
(like get_driver_name) must remain valid for an RCU grace period after
the fence is signaled. However, drm_crtc_cleanup() and the subsequent
freeing of the device do not wait for an RCU grace period via
synchronize_rcu().
If userspace calls ioctl(SYNC_IOC_FILE_INFO) concurrently with a device
hot-unplug:
CPU1 (Userspace)
sync_file_get_name()
ops = rcu_dereference(fence->ops);
if (!dma_fence_test_signaled_flag())
// Preempted or delayed here
CPU2 (Driver Teardown)
Signals the fence (setting fence->ops = NULL)
Destroys and frees the CRTC without waiting for an RCU grace period
CPU1 (Resumes)
ops->get_driver_name(fence) -> drm_crtc_fence_get_driver_name()
crtc = fence_to_crtc(fence); // Casts to the freed CRTC
return crtc->dev->driver->name; // Use-after-free
...
Does the CRTC or DRM device need to be kept alive for the RCU grace
period, or should the fence hold a proper reference to prevent the
use-after-free when get_driver_name() and get_timeline_name() access
the freed CRTC structure?
=== snap ===
I believe this to be a correct observation and this patch implements
the suggestion of waiting for an RCU grace period before proceeding
with destruction of the drm_crtc, so that get_driver_name() and
get_timeline_name() can still work. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/drm_crtc: fix race with dma_fence_signal() in ::get_driver_name()
Since commit 541c8f2468b9 ("dma-buf: detach fence ops on signal v3"),
I'm seeing the BUG_ON() triggering in drm_crtc's fence_to_crtc() via
drm_crtc_fence_get_driver_name() regularly:
Call trace:
panic+0x58/0x5c
die+0x160/0x178
bug_brk_handler+0x70/0xa4
call_el1_break_hook+0x3c/0x1a0
do_el1_brk64+0x24/0x74
el1_brk64+0x34/0x54
el1h_64_sync_handler+0x80/0xfc
el1h_64_sync+0x84/0x88
drm_crtc_fence_get_driver_name+0x60/0x68 (P)
sync_file_get_name+0x184/0x45c
sync_file_ioctl+0x404/0xf70
__arm64_sys_ioctl+0x124/0x1dc
This looks to be caused by a code flow similar to the following:
+++ snip +++
thread A thread B
ioctl(SYNC_IOC_FILE_INFO)
sync_file_ioctl()
sync_file_get_name()
dma_fence_signal_timestamp_locked() dma_fence_driver_name()
ops = rcu_dereference(fence->ops)
if (!dma_fence_test_signaled_flag())
ops->get_driver_name(fence) i.e.
drm_crtc_fence_get_driver_name()
test_and_set_bit(SIGNALED)
RCU_INIT_POINTER(fence->ops, NULL)
drm_crtc_fence_get_driver_name()
BUG_ON(rcu_access_pointer(fence->ops)
!= &drm_crtc_fence_ops)
+++ snap +++
In other words, a fence's ops pointer can now change to NULL on signal,
which wasn't the case before the culprit commit and hence the BUG_ON()
triggers.
Simply drop the BUG_ON() as it's usage of fence ops is invalid now, and
because using BUG_ON() and friends to take down the system is an
unacceptable way to handle a failure.
Note that the adjacent drm_crtc_fence_get_timeline_name() has the same
problem and is fixed by this patch as well. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: reload TDLS header pointer after skb_linearize()
ieee80211_process_tdls_channel_switch() sets tf = skb->data before it
calls skb_linearize(), and reads tf->action_code afterwards.
ieee80211_rx_h_data() queues TDLS channel switch requests and
responses to the interface after pulling only
offsetof(struct ieee80211_tdls_data, u) bytes, so the skb can still be
non-linear when the interface work handles it. Drivers that build
paged RX skbs do this for every frame that does not fit into the skb
head, e.g. iwlwifi (mvm), which is also the only mac80211 driver
that sets NL80211_FEATURE_TDLS_CHANNEL_SWITCH. If the remaining data
does not fit into the tailroom, skb_linearize() moves the data to a
new head and frees the old one, and the action code is then read from
freed memory. Depending on what that memory holds by then, the frame
is handled as before or ends in the WARN_ON_ONCE() of the default
case.
The frame only has to be a data frame with the TDLS ethertype from an
authorized peer, e.g. relayed by the AP from another station in the
BSS; the read happens before the sender is checked to be a TDLS peer.
Load tf after skb_linearize(), as the request and response handlers
already do.
Found by static analysis tool CodeQL. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: Publish the output fence outside of job_lock
job_lock is taken by the V3D interrupt handler, so nesting an IRQ-unsafe
lock under it creates an inversion. drm_syncobj_replace_fence() takes
drm_syncobj::lock, which other paths acquire with interrupts enabled. For
example, a thread interrupted while holding it blocks the handler on
job_lock, and the handler can only make progress once the submit path
releases job_lock, which it cannot do while waiting for drm_syncobj::lock.
This is reported by lockdep:
[ 188.139076] ========================================================
[ 188.139086] WARNING: possible irq lock inversion dependency detected
[ 188.139096] 7.3.0-rc3-00067-gc4f3feeaf60f #67 Tainted: G C
[ 188.139108] --------------------------------------------------------
[ 188.139116] swapper/0/0 just changed the state of lock:
[ 188.139125] ffff0000054f8ff8 (&vc4->job_lock){-...}-{3:3}, at: vc4_irq+0xa8/0x28c [vc4]
[ 188.139234] but this lock took another, HARDIRQ-unsafe lock in the past:
[ 188.139242] (&syncobj->lock){+.+.}-{3:3}
[ 188.139256] and interrupts could create inverse lock ordering between them.
[ 188.139267] other info that might help us debug this:
[ 188.139275] Possible interrupt unsafe locking scenario:
[ 188.139284] CPU0 CPU1
[ 188.139291] ---- ----
[ 188.139299] lock(&syncobj->lock);
[ 188.139312] local_irq_disable();
[ 188.139320] lock(&vc4->job_lock);
[ 188.139335] lock(&syncobj->lock);
[ 188.139350] <Interrupt>
[ 188.139358] lock(&vc4->job_lock);
[ 188.139372] *** DEADLOCK ***
Hand the fence over after job_lock is dropped. The job can complete and
drop exec->fence in that window, so take a reference first and publish
through the local pointer, as exec may already be gone. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: Drop the BO reservations outside of job_lock
vc4_queue_submit() calls drm_exec_fini() with job_lock held and interrupts
disabled. Besides unlocking the reservations, drm_exec_fini() frees the
object array with kvfree(), which asks for preemptible task context or a
non-NMI interrupt, and may reach might_sleep() through vfree().
Considering that an array that exceeds a page can take the vmalloc
fallback, call drm_exec_fini() once job_lock is dropped. The reservations
are then held across the job kick, which is harmless as nothing in the
completion path takes a BO reservation.
Note that vc4_attach_fences() has to stay inside the critical section, as
it walks exec, which the job done worker is free to release as soon as
job_lock is dropped. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: reinstate IEEE80211_TX_CTL_AMPDU flag in ieee80211_tx_prep_agg()
The commit 592234e941f1 ("wifi: mac80211: Fix iTXQ AMPDU fragmentation
handling") changed the way handling of the IEEE80211_TX_CTL_AMPDU flag
is done in mac80211, so the only place it is set is in
ieee80211_tx_dequeue().
This means that any frames that are sent to the driver via drv_tx() will
no longer have the flag set. In particular, this affects packets going
through ieee80211_tx_pending(). Evan reported that this can result in
the ath9k driver failing to account such packets in its block ack
window, eventually overrunning the window and stalling TX.
Fix this by reinstating the flag in ieee80211_tx_prep_agg() when inside
a valid block ack window. This should be harmless for the TXQ path, and
will reinstate the previous behaviour for drivers that use the flag as a
signal to track the packet in the window. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm4: use a full socket for local errors
xfrm4_local_error() passes skb->sk to inet_sk() and ip_local_error()
without ensuring it points to a full socket. TCP SYN-ACK skbs can be owned
by TCP_NEW_SYN_RECV request sockets.
xfrm4_tunnel_check_size() already checks sk_fullsock() since commit
1620c88887b1 ("xfrm: Fix the usage of skb->sk"), so iptfs_is_too_big() is
the only remaining IPv4 caller passing a request socket here: the sk it
tests is the listener, while skb->sk is the request socket.
When IP-TFS rejects such an skb because it exceeds its payload MTU, the
local error path treats the request socket as a struct inet_sock. KASAN
reports a slab-out-of-bounds read in ip_local_error() beyond the
request_sock_TCP allocation.
Resolve the skb owner with skb_to_full_sk() before accessing inet_sock
state or reporting the error. This maps a request socket to its listener
and rejects sockets that cannot be used as full sockets, matching what
commit 6973a21ee73c ("ipv6: xfrm: use full sockets in local error paths")
did for xfrm6_local_error(). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: aic79xx: Fix NULL pointer dereference in device reset
Since commit c67e63800446 ("scsi: aic79xx: Do not reference SCSI command
when resetting device") the device reset SCB has no SCSI command, but
ahd_linux_dev_reset() still sets its residual, and ahd_abort_scbs(), which
completes it, sets its status. Seen on an AIC-7902 when a failing disk
triggered a device reset, which killed the SCSI error handler:
BUG: kernel NULL pointer dereference, address: 0000009c
EIP: ahd_linux_dev_reset.cold+0xee/0x26e
Add NULL command checks to the accessors in aic79xx_osm.h. Also skip
autosense for an SCB without a command and complete it with ahd_done()
right away: the REQUEST SENSE path can clear SCB_DEVICE_RESET, after which
ahd_done() would dereference the missing command. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: Fix demo-mode dynamic ACL dev-entry UAF vs LUN teardown
A demo-mode (generate_node_acls=1) login that allocates a dynamic NodeACL
populates that ACL's per-LUN dev entries in core_tpg_add_node_to_devs()
*before* the ACL is linked onto tpg->acl_node_list by
target_add_node_acl():
core_tpg_check_initiator_node_acl():
...
core_tpg_add_node_to_devs(acl, tpg, NULL); /* builds deves */
target_add_node_acl(acl); /* only now listed */
The LUN teardown sweep, core_clear_lun_from_tpg(), enumerates only
tpg->acl_node_list, so a dev entry whose ACL is still in the window above
is invisible to the sweep and is never disabled. It is left on the
se_lun->lun_deve_list after core_tpg_remove_lun() frees the se_lun; when
the same unpacked_lun is later re-added and the se_lun is reallocated at
the same address, the stale dev entry is rediscovered by
target_nacl_find_deve() and core_enable_device_list_for_node() corrupts
lun_deve_list:
BUG: KASAN: slab-use-after-free ...
core_enable_device_list_for_node+0x5ce/0x880
core_tpg_add_node_to_devs+0x169/0x190
core_dev_add_lun+0x146/0x190
target_fabric_port_link+0xe9/0x1b0
configfs_symlink+0x381/0xae0
__x64_sys_symlink+0x55/0x80
The demo-mode login path that drives the ACL/dev-entry creation is
reachable by an unauthenticated initiator; the colliding LUN add/remove is
a local configfs operation.
Commit 49cb77e297dc ("target: Avoid mappedlun symlink creation during lun
shutdown") introduced se_lun->lun_shutdown and guarded the *explicit* ACL
MappedLUN path (target_fabric_mappedlun_link()), but the demo-mode
automatic path, core_tpg_add_node_to_devs() ->
core_enable_device_list_for_node(), was never given the equivalent guard,
and the publish-after-populate ordering in
core_tpg_check_initiator_node_acl() was left unchanged.
Fix it in three cooperating parts:
1) Publish the dynamic NodeACL onto acl_node_list *before* creating its
dev entries, so the teardown sweep can observe them.
2) Refuse to attach a dev entry to an se_lun that is shutting down,
checked under nacl->lun_entry_mutex -- the same lock the sweep takes --
so once the sweep has passed an ACL any later enable for that LUN
observes lun_shutdown and skips it.
3) In core_enable_device_list_for_node(), insert the new dev entry onto
lun->lun_deve_list while still holding nacl->lun_entry_mutex, in both
the replace and the new-entry branch. Previously the entry was added
to nacl->lun_entry_hlist under the mutex but to lun->lun_deve_list only
after dropping it; with the ACL now published early, the sweep could
take the mutex in that gap, find the entry on the hlist,
core_disable_device_list_for_node() it (list_del() on the not-yet-
linked lun_link succeeds and the entry is freed), and then the enable
would list_add_tail() the freed entry back onto lun_deve_list. Linking
both lists under the mutex makes enable and the sweep mutually
exclusive, closing that window.
core_tpg_add_node_to_devs() already ignores the return value of
core_enable_device_list_for_node(), so a shutting-down LUN is simply
skipped. |
| In the Linux kernel, the following vulnerability has been resolved:
9p/xen: validate the response size from the backend
p9_xen_response() takes the length of an incoming response from the ring
-- the first field of the 9p header, which the Xen transport reuses as
its framing header -- and uses it to advance the consumer index, but
never checks that it is at least the header size or no larger than the
number of bytes the backend has actually produced.
A malicious or buggy backend can post a response whose size is smaller
than the header (for example 0). The consumer index then never advances,
so the response work re-reads the same ring contents instead of making
progress. In testing this raced with the teardown that the malformed
reply triggers and dereferenced a freed p9_client:
9pfs 9pfs-0: Wrong req tag=ffff
BUG: kernel NULL pointer dereference, address: 0000000000000060
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 7.2.0-rc5 #6 PREEMPT(lazy)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
Workqueue: events p9_xen_response
RIP: 0010:idr_find+0x4/0x10
RSP: 0018:ffffbf5d80063de8 EFLAGS: 00010202
RAX: 0000000000000001 RBX: ffffa229c21195a0 RCX: ffffa229c2400000
RDX: ffffa229c11c2200 RSI: 000000000000ffff RDI: 0000000000000050
RBP: 000000000000ffff R08: 3fffffffffffdfff R09: ffffffffffffffff
R10: 3fffffffffffdfff R11: ffffffff87a60e80 R12: 0000000000000050
R13: 0000000000000000 R14: 000000000000ffff R15: 0000000000100000
FS: 0000000000000000(0000) GS:ffffa22a7661c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000060 CR3: 000000003ac34002 CR4: 0000000000770ef0
PKRU: 55555554
Call Trace:
<TASK>
p9_tag_lookup+0x2b/0x90
p9_xen_response+0x17c/0x2e0
process_one_work+0x16a/0x3a0
worker_thread+0x172/0x2e0
kthread+0xdd/0x110
ret_from_fork+0x18b/0x240
ret_from_fork_asm+0x1a/0x30
</TASK>
Modules linked in:
CR2: 0000000000000060
---[ end trace 0000000000000000 ]---
Reject a response whose size is outside [sizeof(header), queued] before
using it, matching the validation the backend already applies to
incoming requests. |
| In the Linux kernel, the following vulnerability has been resolved:
9p: don't decrement a server-owned zero nlink
A 9P2000.L server can report nlink=0 for a regular file that still
exists. On a cache=loose or cache=fscache mount, lookup stores that
value with set_nlink(). A later successful unlink calls
v9fs_dec_count(), which still calls drop_nlink() for a non-directory.
drop_nlink() warns, and the unsigned link count wraps to 4294967295.
fstat() on a descriptor opened before the unlink shows 0 before and
4294967295 after.
The warning on the unpatched kernel, trimmed:
WARNING: fs/inode.c:408 at drop_nlink+0xac/0xd0, CPU#1: trigger/188
CPU: 1 UID: 0 PID: 188 Comm: trigger Tainted: G N 7.3.0-rc4-00537-ga3ff15db6820 #1 PREEMPT(lazy)
RIP: 0010:drop_nlink+0xac/0xd0
Call Trace:
<TASK>
v9fs_remove+0x529/0x750
vfs_unlink+0x2f0/0xbd0
filename_unlinkat+0x340/0x6c0
__x64_sys_unlink+0x46/0x70
do_syscall_64+0xe8/0x4f0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
---[ end trace 0000000000000000 ]---
Directories whose cached nlink is at most 2 already skip this
decrement, because the exported filesystem may not maintain nlink
(commit ac89b2ef9b559). cache=none skips it as well (commit
574aa0b479947). cache=mmap does not take this path: it sets neither
CACHE_META nor CACHE_LOOSE. A regular file on cache=loose or
cache=fscache still does. Its count came from GETATTR and may
already be zero, so skip the decrement when i_nlink is already 0.
Verified on 7.3-rc4-00537-ga3ff15db6820 with only this change. A
server that advertises nlink=0 and accepts the unlink no longer
warns, and the open descriptor stays at nlink 0. An honest server
on the same mount still goes from 1 to 0. A rejected unlink leaves
the count unchanged. cache=none is unchanged. With panic_on_warn
the unpatched kernel panics on the warning; the patched kernel does
not. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: mcast: validate tracker padding before forwarding
A multicast tracker with an even number of destinations needs two
padding bytes after its destination list. batadv_mcast_forw_packet()
currently only checks that the count field and the addresses fit in
the tracker TVLV.
If an unpadded even tracker is compacted to an odd number of
destinations, batadv_mcast_forw_shrink_update_headers() includes those
missing padding bytes in the amount to remove. The subsequent memmove
can then write two bytes past the old packet tail. With no tailroom,
this corrupts skb_shared_info.
Include the required padding in the existing tracker length check.
This rejects the malformed tracker before either received or locally
generated packets can reach the compactor. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: stop originator purge worker before freeing TT
batadv_mesh_free() releases the translation tables via batadv_tt_free()
before batadv_originator_free() stops orig_work. The purge worker can
therefore still run while the TT is torn down. When an originator times
out, batadv_purge_orig_ref() calls batadv_tt_global_del_orig(), which
loads tt.global_hash and walks all buckets while taking their locks:
CPU0 CPU1
batadv_tt_free() batadv_purge_orig()
batadv_tt_global_del_orig()
hash = ...tt.global_hash;
batadv_tt_global_table_free()
batadv_hash_destroy(hash);
spin_lock_bh(&hash->list_locks[i]);
Disable orig_work at the beginning of batadv_mesh_free(), directly after
the mesh was marked as deactivating. The second
disable_delayed_work_sync() in batadv_originator_free() is harmless because
it is free'd anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: ignore ROAM flag of received ADD changes
A received TT change (OGM diff or full table response) with the ROAM flag
but without DEL is handled by batadv_tt_global_add() like a ROAMING_ADV:
* a newly created global entry gets BATADV_TT_CLIENT_ROAM and is
therefore excluded from the global CRC. The sender has it in its local
CRC and the receiver has to request the full table again
* batadv_tt_global_purge_local() removes the local entry of the
receiver. The receiver's own client is considered as roamed to the sender
and frames for it are rerouted
The ROAM flag only has a meaning together with DEL. Drop it on reception to
keep it from populating the global table with a temporary ROAMING entry
which is not part of the CRC - and therefore causing a CRC mismatch. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: don't drop local events queued during TVLV update
batadv_tt_tvlv_container_update() read the number of local changes without
holding changes_list_lock. batadv_tt_local_event() is not serialized by
the commit_lock and can queue new events before the changes_list is
flushed:
CPU0 CPU1
batadv_tt_tvlv_container_update()
num = ...local_changes;
batadv_tt_local_event()
list_add_tail(...);
...local_changes++;
spin_lock_bh(&...changes_list_lock);
/* only num events copied but all freed */
The additional events were freed without ever being sent. Other nodes will
only notice this via a CRC mismatch and must request the full table.
The number of changes and the changes_list must therefore be taken
atomically. Events queued afterwards then stay in the tt.changes_list for
the next TT round.
The changes can no longer be kept for the next round when the TVLV buffer
allocation fails. But they would be sent with a skipped TTVN anyway, so the
other nodes have to request the full table in this case either way. The
last changeset is only dropped in this case when the TTVN was incremented.
Without new changes, it still describes the current TTVN.
Previously, the unconsumed changes caused a retry of the TVLV container
update in the next commit round. Since the changes are now consumed, the
next round would only take the path without changes and wait for
BATADV_TT_OGM_APPEND_MAX rounds before updating the container again. Until
then, the outdated container with the previous TTVN would still be
announced. The ogm_append_cnt is therefore reset on failure to retry the
update in the next OGM interval.
This doesn't make the CRC consistent with the announced changeset. The
local table modifications are still not serialized with the commit and
batadv_tt_local_transition_new() can still make a client part of the CRC
for which the event is only part of the next TT round. Such an
inconsistency is detected by the CRC check of the other nodes and solved
via a full table request. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: account for chunk padding in sctp_init_cause()
sctp_init_cause() accepts a chunk when skb_tailroom() can hold the
cause header and the payload. sctp_addto_chunk() then writes 0-3
bytes of padding before that header so the chunk stays 4-byte
aligned. The check does not include the padding, and the following
skb_put() calls skb_over_panic() from softirq.
Count the padding sctp_addto_chunk() is about to write. The cause
length on the wire stays the header plus the payload.
Found by LLM inspection, triggered and tested the fix. |