| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
KEYS: trusted: Fix TPM teardown ordering
trusted_tpm_exit() drops the TPM chip reference and frees the digest
array before unregistering the trusted key type. key_type_lookup()
holds key_types_sem for reading until the key operation finishes, while
unregister_key_type() takes it for writing. It therefore provides the
synchronization point that must precede backend teardown.
The current order permits this interleaving:
CPU 0 CPU 1
trusted_tpm_exit() key_type_lookup("trusted")
put_device(&chip->dev) trusted_tpm_seal()
kfree(digests) pcrlock()
unregister_key_type() tpm_pcr_extend(..., digests)
CPU 1 can consequently dereference the freed digest array. The chip can
also be released before callbacks stop using it.
KASAN reported:
BUG: KASAN: slab-use-after-free in tpm_pcr_extend+0x1f0/0x200
Read of size 2 at addr ffff88810872d000 by task poc/89
Call Trace:
tpm_pcr_extend+0x1f0/0x200
pcrlock+0x42/0x70 [trusted]
trusted_tpm_seal+0x1b6/0x570 [trusted]
trusted_instantiate+0x293/0x340 [trusted]
__key_instantiate_and_link+0xb2/0x2b0
__key_create_or_update+0x61e/0xb50
__do_sys_add_key+0x1b8/0x310
Allocated by task 88:
__kmalloc_noprof+0x1a7/0x490
do_one_initcall+0xa1/0x390
do_init_module+0x2df/0x840
Freed by task 90:
kfree+0x131/0x3c0
trusted_tpm_exit+0x59/0xa0 [trusted]
__do_sys_delete_module+0x346/0x510
Move unregister_key_type() before releasing either resource. This stops
new lookups and waits for in-flight key operations to finish before the
backend state is destroyed. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/migrate_device: clear stale mapping after freeing swapcache
__migrate_device_pages() reads the folio mapping before calling
folio_free_swap(). When folio_free_swap() succeeds, the folio is removed
from the swap cache, but the saved mapping still points to swap_space.
Passing the stale mapping to folio_migrate_mapping() makes it use the
mapped-folio path for a folio that is no longer in swapcache. It can then
operate on swap_space.i_pages with invalid reference accounting,
eventually triggering a folio reference count BUG.
After a successful split, nr still contains the number of pages in the
original large folio, although each resulting page is now a separate
order-0 folio. Reset nr to 1 so each split folio is processed separately,
including its own swapcache removal and mapping lookup.
Refresh the saved mapping after folio_free_swap() so the current folio
state is used during migration. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/ras: Fix cxl_rch_get_aer_info() out-of-bounds AER register read
cxl_rch_get_aer_info() copies the RCH Downstream Port AER capability from
the RCRB MMIO block using a readl() loop bounded by sizeof(struct
aer_capability_regs). This struct is a software layout and its embedded
struct pcie_tlp_log is larger than the on-wire AER capability. As a
result the loop reads past the mapped AER register block.
The over-read also populates the software-only tail fields including
header_log.header_len. An out-of-range header_len passed to
pcie_print_tlp_log() can then loop past the header log buffer and cause
a second out-of-bounds read.
The read was correct when introduced, but struct pcie_tlp_log has since
grown (Header Log and TLP Prefix Log sizes, header_len and flit fields),
so sizeof(struct aer_capability_regs) no longer matches the physical AER
capability.
Bound the read to the physical AER registers, header through the 16 byte
Header Log. Zero the destination first so the software-only fields are
deterministic. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: check nfsd4_acl_to_attr() return value in nfsd4_create()
nfsd4_create() stores the return value of nfsd4_acl_to_attr() in
status, but the switch(create->cr_type) block unconditionally
overwrites it in every branch. ACL translation errors are silently
discarded, and the CREATE proceeds without the requested ACL.
Add an early exit check after nfsd4_acl_to_attr(), matching the
pattern already used in nfsd4_setattr().
[ cel: prefer NFS4ERR_BADTYPE over NFS4ERR_ATTRNOTSUPP ] |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix clock domain mismatch in clients_still_reclaiming()
clients_still_reclaiming() computes a deadline from nn->boot_time
(CLOCK_REALTIME, ~1.7 billion) but compares it against
ktime_get_boottime_seconds() (CLOCK_BOOTTIME, seconds since boot).
The comparison is always false — it would take ~54 years of uptime
for BOOTTIME to exceed the REALTIME-derived deadline.
This means any client can hold the server in grace indefinitely by
sending CLAIM_PREVIOUS OPEN requests, blocking all non-reclaim
operations for all other clients.
Add boot_time_bt (CLOCK_BOOTTIME) alongside the existing boot_time
and use it for the deadline computation. boot_time (CLOCK_REALTIME)
is preserved for its cl_boot clientid-nonce role. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: close shrinker/GC/fsnotify vs per-net shutdown race in filecache
The shrinker, GC worker, and fsnotify/lease callbacks can unhash an
nfsd_file from the rhashtable and then call
nfsd_file_dispose_list_delayed() to move it to the per-net dispose list.
If nfsd_file_cache_shutdown_net() runs concurrently, its rhashtable walk
misses the already-unhashed file, and its drain of the per-net dispose
list can run before the file has been queued. The file then sits on
the per-net list with no thread to drain it, leaking both the file and
its associated state.
The GC worker and shrinker already hold nfsd_gc_lock while walking the
LRU, but in the original code they release it before calling
nfsd_file_dispose_list_delayed(). The fsnotify/lease path
(nfsd_file_close_inode) has no synchronization at all.
Fix this by:
1. Widening nfsd_gc_lock in both nfsd_file_gc() and nfsd_file_lru_scan()
to cover the nfsd_file_dispose_list_delayed() call.
2. Wrapping nfsd_file_close_inode() in nfsd_gc_lock so that all three
callers of nfsd_file_dispose_list_delayed() hold the lock.
3. Adding a spin_lock/unlock(nfsd_gc_lock) barrier in
nfsd_file_cache_shutdown_net() after the purge, so that any
in-progress disposal has fully completed before the per-net list
is drained.
All operations inside the lock are non-sleeping (rhashtable lookups,
atomic bit/refcount ops, list moves, svc_wake_up), so the spinlock is
appropriate. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: universal-pidff: stop the device when force-feedback init fails
universal_pidff_probe() starts the device with hid_hw_start() and then, if
force-feedback initialisation fails, returns the error through a label that
only does "return error". The device is left started.
The HID core does not unwind on the driver's behalf. __hid_device_probe()
releases the devres group, closes the report and clears hdev->driver:
if (ret) {
devres_release_group(&hdev->dev, hdev->devres_group_id);
hid_close_report(hdev);
hdev->driver = NULL;
}
The hidraw character device that hid_hw_start() registered through
hid_connect() is allocated with kzalloc() and added with cdev_device_add(),
so it is not devres-managed and survives that. With hdev->driver NULL,
hid_device_remove() skips hid_hw_stop() as well, because it only unwinds
while a driver is still attached. The registration therefore outlives the
device on both paths.
Opening the surviving /dev/hidrawX writes into freed memory. KASAN reports
a use-after-free write from hidraw_open() -> hid_hw_open() -> the
transport's open callback, which takes a spinlock inside the freed object.
A descriptor that carries a PID usage page and no input reports is enough:
hidraw claims the device so hid_hw_start() succeeds, while hid->inputs
stays empty so force-feedback init fails. The other failure returns in
hid_pidff_init_with_quirks() - no output reports, an allocation failure,
pidff_init_fields(), pidff_check_autocenter(), an unusable effect count,
input_ff_create() - all reach the same label.
Stop the device on that path. hid-dr.c and hid-emsff.c, which start the
device with the same HID_CONNECT_DEFAULT & ~HID_CONNECT_FF mask, already do
this. The two earlier gotos must keep returning without hid_hw_stop(),
since neither has a started device, so give the path that fails after the
start its own label.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
HID: mcp2221: clear rxbuf after I2C/SMBus transfer completes
mcp_i2c_smbus_read() stores the caller-supplied buffer pointer in
mcp->rxbuf for the duration of a transfer but never clears it when the
transfer finishes or times out. Once the caller frees or reuses the
buffer, mcp->rxbuf becomes a dangling pointer. A delayed or spurious
MCP2221_I2C_GET_DATA report can then drive mcp2221_raw_event() to
memcpy device data into the freed memory, causing a write
use-after-free.
Route all return paths through a single exit point that clears
mcp->rxbuf and mcp->rxbuf_size, so that the existing !mcp->rxbuf guard
in the raw_event handler can reject any report arriving after the
transfer has ended. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: skip sufficiently large global buffers when resizing
z_erofs_gbuf_nrpages is advanced only after every global buffer has been
grown. If a resize fails after some buffers were enlarged, a retry
revisits those enlarged buffers.
Retrying the same size then returns -ENOMEM because alloc_pages_bulk()
has no pages to add and the unchanged return value is treated as a
failure. Retrying an intermediate size allocates a temporary pointer
array smaller than gbuf->nrpages and copies more existing pointers than
the array can hold.
Skip buffers that already satisfy the request. Once all remaining
buffers have caught up, advancing z_erofs_gbuf_nrpages again describes
the guaranteed minimum size across the pool. |
| In the Linux kernel, the following vulnerability has been resolved:
ip: orphan prefetched skbs before multicast forwarding
IPv4 and IPv6 input preserve an skb->sk association installed by
bpf_sk_assign() so that local delivery can use the selected socket under
RCU. Both address families can also prefetch a socket in UDP early demux.
In both paths (BPF and UDP early demux) a reference is not guaranteed to
be held on the socket.
When a multicast packet is not locally deliverable, IPv6 hands the
original skb to ip6_mr_input(). IPv4's ip_mr_input() similarly keeps the
original skb when local delivery is not needed. Either path can put the
skb on an unresolved multicast route queue or forward it after the
receive-side RCU section ends.
After the prefetched socket is destroyed, a later skb free invokes
sock_pfree() and dereferences the stale skb->sk. Orphan the skb before
each non-local multicast forwarding path. Local delivery retains the
original skb; the existing skb_clone() calls provide multicast forwarding
with a socket-free clone. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: rpl: fix NULL dereference of idev in ipv6_rpl_srh_rcv()
ipv6_rpl_srh_rcv() dereferences idev from __in6_dev_get() without a NULL
check when reading idev->cnf.rpl_seg_enabled.
When the device's MTU drops below IPV6_MIN_MTU, addrconf_ifdown() clears
dev->ip6_ptr through RCU_INIT_POINTER(). A packet that passed the idev
check in ip6_rcv_core() can then reach ipv6_rpl_srh_rcv() with
dev->ip6_ptr already NULL.
Reproduced by flooding the receiving interface with ping6 traffic while
flapping its MTU between 1500 and 1200:
BUG: KASAN: null-ptr-deref in ipv6_rpl_srh_rcv+0xb3/0x1070
Read of size 4 at addr 00000000000006b4 by task ping6/394
CPU: 2 UID: 0 PID: 394 Comm: ping6 Not tainted 7.2.0-rc7-micro-vm-dev-00095-g24ef02f934ee #240 PREEMPT(full)
Call Trace:
<IRQ>
kasan_report+0xc6/0x100
ipv6_rpl_srh_rcv+0xb3/0x1070
ip6_protocol_deliver_rcu+0x759/0x9a0
ip6_input_finish+0xa8/0x1b0
ip6_input+0xe1/0x490
ipv6_rcv+0x33d/0x460
__netif_receive_skb_one_core+0xd6/0x130
process_backlog+0x2cc/0xa00
__napi_poll.constprop.0+0x56/0x270
net_rx_action+0x327/0x730
handle_softirqs+0x11e/0x630
do_softirq+0xb3/0xf0
</IRQ>
Both ipv6_rpl_srh_rcv() and ipv6_srh_rcv() are called only from
ipv6_rthdr_rcv(), which already has an idev lookup.
Fix the NULL dereference on the RPL path by checking idev in
ipv6_rthdr_rcv(), before it calls either function. The callees take idev as
an argument and no longer call __in6_dev_get(), so the packet is now
dropped in one place, with SKB_DROP_REASON_IPV6DISABLED on both paths. |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: defer rq_argp and rq_resp free until after RCU grace period
svc_rqst_free() frees rqstp->rq_argp and rqstp->rq_resp synchronously
via kfree(), but defers the rqstp struct free via kfree_rcu(). After
svc_exit_thread() calls list_del_rcu() and svc_rqst_free(), there is
a window where RCU readers that started before list_del_rcu() can still
traverse the thread list and find the rqstp. These readers (e.g.
nfsd_nl_rpc_status_get_dumpit()) dereference rqstp->rq_argp, which has
already been freed — a use-after-free.
Fix this by moving the kfree of rq_argp and rq_resp into an explicit
call_rcu() callback alongside the struct free. Resources not accessed
by RCU readers (bvec, buffer pages, scratch folio, auth_data) remain
synchronously freed. |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: fix gssx_dec_option_array error path bugs
Four coupled defects in the gssx XDR option-array decoder make the
error paths unsafe: a NULL deref in the caller, a refcount leak on
the decoded group_info, and a latent use-after-free that the leak
fix would otherwise expose.
gssx_dec_option_array() sets oa->count = 1 before allocating
oa->data. If that allocation fails, -ENOMEM is returned with
oa->count == 1 and oa->data == NULL. All other error paths jump
to free_oa: which frees oa->data and NULLs it but also leaves
oa->count == 1. The caller trusts the count:
gssp_accept_sec_context_upcall()
gssx_dec_accept_sec_context()
gssx_dec_option_array() /* fails, count=1 data=NULL */
data = res.options.data[0].value /* NULL deref */
Independently, free_creds: releases the partially decoded svc_cred
with a bare kfree(creds). gssx_dec_linux_creds() installs a
groups_alloc() result into creds->cr_group_info; that object is
kvmalloc-backed and refcounted, and only put_group_info() reaches
kvfree(). A plain kfree(creds) drops the wrapper and leaks the
group_info allocation.
The natural fix for the leak is to call free_svc_cred(creds) before
kfree(creds), but free_svc_cred() invokes put_group_info() on
creds->cr_group_info unconditionally when non-NULL. The existing
out_free_groups: path in gssx_dec_linux_creds() already called
groups_free() on that pointer without clearing it, so once
free_svc_cred() is wired in, the subsequent put_group_info() would
touch freed memory.
Fix all four together:
- Move the oa->count = 1 assignment below the oa->data allocation
so it is never set when oa->data is NULL.
- Reset oa->count to 0 at free_oa: so count and data stay
coherent and the caller sees an empty option array.
- Call free_svc_cred(creds) before kfree(creds) at free_creds:
so the refcounted cr_group_info is released. free_svc_cred()
either NULL-guards each field explicitly (cr_group_info has
an if() check) or delegates to a helper that is NULL-safe
itself (kfree for the string fields, gss_mech_put() which
guards with if(gm) at gss_mech_switch.c:342), so it is safe
to call on a partially decoded svc_cred where only
cr_uid/cr_gid/cr_group_info have been written and everything
else is zero from kzalloc.
- In gssx_dec_linux_creds()'s out_free_groups: path, release
cr_group_info with put_group_info() rather than groups_free()
so the teardown matches free_svc_cred()'s refcount-aware path,
and clear the pointer so a later free_svc_cred() on the same
creds does not release it a second time. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: Reorder rpcrdma_rn_unregister before rdma_destroy_id
svc_rdma_free() caches rdma->sc_cm_id->device before teardown,
then calls rdma_destroy_id(sc_cm_id) which frees the cm_id.
rpcrdma_rn_unregister() follows, but between those two calls
the transport's sc_rn entry is still installed in the device's
rd_xa. A concurrent ib_unregister_device walk can dispatch
svc_rdma_xprt_done() against the now-freed sc_cm_id.
Move rpcrdma_rn_unregister() before rdma_destroy_id() so the
transport's notification entry is removed from the xarray before
the cm_id it references is destroyed.
Also guard the sc_cm_id dereference with a NULL check: the
following patches introduce paths that reach svc_rdma_free()
with sc_cm_id == NULL (listener create failure, ADDR_CHANGE
replacement failure). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: cancel SSR work items during PCI shutdown
A reboot can crash the kernel if it overlaps with WLAN firmware crash
recovery (SSR). The crash is a NULL pointer dereference in the MHI teardown
path while freeing DMA-backed MHI contexts.
Simplified trace:
dma_free_attrs
mhi_deinit_dev_ctxt [mhi]
ath11k_pci_power_down [ath11k_pci]
ath11k_pci_shutdown [ath11k_pci]
device_shutdown
kernel_restart
On the host side, SSR is driven by the MHI RDDM callback, which queues
reset_work to perform device recovery. reset_work power-cycles the device
by calling ath11k_hif_power_down() followed by ath11k_hif_power_up(). The
power-down phase deinitializes MHI and frees DMA resources.
Shutdown/reboot runs fully asynchronously with this RDDM-driven SSR
recovery flow. As a result, the shutdown path
(ath11k_pci_shutdown() -> ath11k_pci_power_down()) can race with the SSR
recovery sequence.
Fix this by canceling SSR-related work items during PCI shutdown, marking
the device as unregistering, and serializing the RDDM callback path that
checks and queues reset_work. This ensures that no new SSR recovery work
can be queued once teardown has started, and that any in-flight recovery
work is fully synchronized before device power-down, preventing MHI
teardown and DMA resource freeing from running more than once.
Note: This issue only affects PCI/MHI-based devices. AHB-based ath11k
devices do not queue reset_work in normal SSR flows.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04866.5-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1 |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix writes_pending and barrier reference leaks on discard failures
raid10_make_request() acquires a writes_pending reference with
md_write_start() before calling raid10_handle_discard(). Several failure
paths in raid10_handle_discard() complete the bio and return without
releasing the corresponding reference, causing md_write_end() to be
skipped.
Call md_write_end() before returning from these failure paths to keep
writes_pending accounting balanced.
Additionally, discard split allocation failures can occur after
wait_barrier() succeeds. Those paths return without calling
allow_barrier(), leaking the associated barrier reference.
Release the barrier before returning from those paths. |
| Type confusion in V8 in Google Chrome prior to 153.0.8010.52 allowed a remote attacker leveraging social engineering to execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| Red Hat Product Security has come to the conclusion that this CVE is not needed. |
| Memory Corruption via Uncanceled AIO Requests on Error: libkcapi's one-shot AIO path can return an error before all submitted IOCBs are drained, allowing later kernel writes into caller-owned output buffers. |
| A flaw was found in environment-modules. A local attacker can exploit this vulnerability by placing a maliciously named modulefile in a location visible to the victim's `MODULEPATH`. When the victim uses Bash completion for `module` or `ml` commands, the malicious module name, containing shell metacharacters, is evaluated as a command. This can lead to arbitrary command execution in the completing user's shell, impacting their confidentiality, integrity, and availability. |
