| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
HID: universal-pidff: stop the device when force-feedback init fails
universal_pidff_probe() starts the device with hid_hw_start() and then, if
force-feedback initialisation fails, returns the error through a label that
only does "return error". The device is left started.
The HID core does not unwind on the driver's behalf. __hid_device_probe()
releases the devres group, closes the report and clears hdev->driver:
if (ret) {
devres_release_group(&hdev->dev, hdev->devres_group_id);
hid_close_report(hdev);
hdev->driver = NULL;
}
The hidraw character device that hid_hw_start() registered through
hid_connect() is allocated with kzalloc() and added with cdev_device_add(),
so it is not devres-managed and survives that. With hdev->driver NULL,
hid_device_remove() skips hid_hw_stop() as well, because it only unwinds
while a driver is still attached. The registration therefore outlives the
device on both paths.
Opening the surviving /dev/hidrawX writes into freed memory. KASAN reports
a use-after-free write from hidraw_open() -> hid_hw_open() -> the
transport's open callback, which takes a spinlock inside the freed object.
A descriptor that carries a PID usage page and no input reports is enough:
hidraw claims the device so hid_hw_start() succeeds, while hid->inputs
stays empty so force-feedback init fails. The other failure returns in
hid_pidff_init_with_quirks() - no output reports, an allocation failure,
pidff_init_fields(), pidff_check_autocenter(), an unusable effect count,
input_ff_create() - all reach the same label.
Stop the device on that path. hid-dr.c and hid-emsff.c, which start the
device with the same HID_CONNECT_DEFAULT & ~HID_CONNECT_FF mask, already do
this. The two earlier gotos must keep returning without hid_hw_stop(),
since neither has a started device, so give the path that fails after the
start its own label.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
HID: mcp2221: clear rxbuf after I2C/SMBus transfer completes
mcp_i2c_smbus_read() stores the caller-supplied buffer pointer in
mcp->rxbuf for the duration of a transfer but never clears it when the
transfer finishes or times out. Once the caller frees or reuses the
buffer, mcp->rxbuf becomes a dangling pointer. A delayed or spurious
MCP2221_I2C_GET_DATA report can then drive mcp2221_raw_event() to
memcpy device data into the freed memory, causing a write
use-after-free.
Route all return paths through a single exit point that clears
mcp->rxbuf and mcp->rxbuf_size, so that the existing !mcp->rxbuf guard
in the raw_event handler can reject any report arriving after the
transfer has ended. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: skip sufficiently large global buffers when resizing
z_erofs_gbuf_nrpages is advanced only after every global buffer has been
grown. If a resize fails after some buffers were enlarged, a retry
revisits those enlarged buffers.
Retrying the same size then returns -ENOMEM because alloc_pages_bulk()
has no pages to add and the unchanged return value is treated as a
failure. Retrying an intermediate size allocates a temporary pointer
array smaller than gbuf->nrpages and copies more existing pointers than
the array can hold.
Skip buffers that already satisfy the request. Once all remaining
buffers have caught up, advancing z_erofs_gbuf_nrpages again describes
the guaranteed minimum size across the pool. |
| In the Linux kernel, the following vulnerability has been resolved:
acpi/apei/ghes: Use raw_spinlock_t for CXL CPER work locks
The CXL CPER work registration and unregistration helpers acquire
cxl_cper_work_lock and cxl_cper_prot_err_work_lock with a spinlock
guard(), which leaves local interrupts enabled. The corresponding post
paths (cxl_cper_post_event(), cxl_cper_post_prot_err()) execute in hard
IRQ context (they are called from the GHES error notification path) and
acquire the same locks with an irqsave guard().
If a CPU is holding one of these locks via a spinlock guard() when a GHES
interrupt arrives on the same CPU, the IRQ handler spins on the held lock
waiting for it to release, while the lock holder is preempted by the IRQ.
The result is a deadlock.
Convert both locks from spinlock_t to raw_spinlock_t and use guard() at
all call sites. On PREEMPT_RT kernels spinlock_t is backed by rt_mutex and
sleeping from hard IRQ context is not permitted; raw_spinlock_t is safe in
both contexts.
Add WARN_ONCE to both register functions to surface double-registration
bugs at runtime.
Restructure both unregister functions to clear the global work pointer
under the lock before calling cancel_work_sync(), closing the window
where a CPER interrupt could schedule work on a pointer about to be
freed. Add kfifo_reset() after cancel_work_sync() so stale entries
are not replayed on next module load.
Both kfifos are single-consumer: only one work_struct is registered at
a time, enforced by the WARN_ONCE guard in the register functions.
kfifo_reset() is safe outside the lock because cancel_work_sync() has
already quiesced the consumer, and no new consumer can register until
the current module exit completes and a fresh module init runs.
Remove the redundant cancel_work_sync() call from cxl_ras_exit() and
cxl_pci_driver_exit(). The CPER unregister functions now quiesce
the work internally. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: apple-soc: Fix OPP table cleanup
apple_soc_cpufreq_init() adds OPP tables from firmware, but
some failure paths do not remove them. The driver also uses
dev_pm_opp_remove_all_dynamic(), which is not the right cleanup
helper for OPP tables loaded from firmware.
Use the cpumask OPP helper after the policy CPU mask has been
populated. Pair it with the matching cpumask remove helper on
failure paths and in apple_soc_cpufreq_exit(). This also removes
the separate dev_pm_opp_set_sharing_cpus() call, as the cpumask
helper loads the DT OPP tables for all CPUs in the policy. |
| In the Linux kernel, the following vulnerability has been resolved:
ip: orphan prefetched skbs before multicast forwarding
IPv4 and IPv6 input preserve an skb->sk association installed by
bpf_sk_assign() so that local delivery can use the selected socket under
RCU. Both address families can also prefetch a socket in UDP early demux.
In both paths (BPF and UDP early demux) a reference is not guaranteed to
be held on the socket.
When a multicast packet is not locally deliverable, IPv6 hands the
original skb to ip6_mr_input(). IPv4's ip_mr_input() similarly keeps the
original skb when local delivery is not needed. Either path can put the
skb on an unresolved multicast route queue or forward it after the
receive-side RCU section ends.
After the prefetched socket is destroyed, a later skb free invokes
sock_pfree() and dereferences the stale skb->sk. Orphan the skb before
each non-local multicast forwarding path. Local delivery retains the
original skb; the existing skb_clone() calls provide multicast forwarding
with a socket-free clone. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: rpl: fix NULL dereference of idev in ipv6_rpl_srh_rcv()
ipv6_rpl_srh_rcv() dereferences idev from __in6_dev_get() without a NULL
check when reading idev->cnf.rpl_seg_enabled.
When the device's MTU drops below IPV6_MIN_MTU, addrconf_ifdown() clears
dev->ip6_ptr through RCU_INIT_POINTER(). A packet that passed the idev
check in ip6_rcv_core() can then reach ipv6_rpl_srh_rcv() with
dev->ip6_ptr already NULL.
Reproduced by flooding the receiving interface with ping6 traffic while
flapping its MTU between 1500 and 1200:
BUG: KASAN: null-ptr-deref in ipv6_rpl_srh_rcv+0xb3/0x1070
Read of size 4 at addr 00000000000006b4 by task ping6/394
CPU: 2 UID: 0 PID: 394 Comm: ping6 Not tainted 7.2.0-rc7-micro-vm-dev-00095-g24ef02f934ee #240 PREEMPT(full)
Call Trace:
<IRQ>
kasan_report+0xc6/0x100
ipv6_rpl_srh_rcv+0xb3/0x1070
ip6_protocol_deliver_rcu+0x759/0x9a0
ip6_input_finish+0xa8/0x1b0
ip6_input+0xe1/0x490
ipv6_rcv+0x33d/0x460
__netif_receive_skb_one_core+0xd6/0x130
process_backlog+0x2cc/0xa00
__napi_poll.constprop.0+0x56/0x270
net_rx_action+0x327/0x730
handle_softirqs+0x11e/0x630
do_softirq+0xb3/0xf0
</IRQ>
Both ipv6_rpl_srh_rcv() and ipv6_srh_rcv() are called only from
ipv6_rthdr_rcv(), which already has an idev lookup.
Fix the NULL dereference on the RPL path by checking idev in
ipv6_rthdr_rcv(), before it calls either function. The callees take idev as
an argument and no longer call __in6_dev_get(), so the packet is now
dropped in one place, with SKB_DROP_REASON_IPV6DISABLED on both paths. |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: defer rq_argp and rq_resp free until after RCU grace period
svc_rqst_free() frees rqstp->rq_argp and rqstp->rq_resp synchronously
via kfree(), but defers the rqstp struct free via kfree_rcu(). After
svc_exit_thread() calls list_del_rcu() and svc_rqst_free(), there is
a window where RCU readers that started before list_del_rcu() can still
traverse the thread list and find the rqstp. These readers (e.g.
nfsd_nl_rpc_status_get_dumpit()) dereference rqstp->rq_argp, which has
already been freed — a use-after-free.
Fix this by moving the kfree of rq_argp and rq_resp into an explicit
call_rcu() callback alongside the struct free. Resources not accessed
by RCU readers (bvec, buffer pages, scratch folio, auth_data) remain
synchronously freed. |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: fix gssx_dec_option_array error path bugs
Four coupled defects in the gssx XDR option-array decoder make the
error paths unsafe: a NULL deref in the caller, a refcount leak on
the decoded group_info, and a latent use-after-free that the leak
fix would otherwise expose.
gssx_dec_option_array() sets oa->count = 1 before allocating
oa->data. If that allocation fails, -ENOMEM is returned with
oa->count == 1 and oa->data == NULL. All other error paths jump
to free_oa: which frees oa->data and NULLs it but also leaves
oa->count == 1. The caller trusts the count:
gssp_accept_sec_context_upcall()
gssx_dec_accept_sec_context()
gssx_dec_option_array() /* fails, count=1 data=NULL */
data = res.options.data[0].value /* NULL deref */
Independently, free_creds: releases the partially decoded svc_cred
with a bare kfree(creds). gssx_dec_linux_creds() installs a
groups_alloc() result into creds->cr_group_info; that object is
kvmalloc-backed and refcounted, and only put_group_info() reaches
kvfree(). A plain kfree(creds) drops the wrapper and leaks the
group_info allocation.
The natural fix for the leak is to call free_svc_cred(creds) before
kfree(creds), but free_svc_cred() invokes put_group_info() on
creds->cr_group_info unconditionally when non-NULL. The existing
out_free_groups: path in gssx_dec_linux_creds() already called
groups_free() on that pointer without clearing it, so once
free_svc_cred() is wired in, the subsequent put_group_info() would
touch freed memory.
Fix all four together:
- Move the oa->count = 1 assignment below the oa->data allocation
so it is never set when oa->data is NULL.
- Reset oa->count to 0 at free_oa: so count and data stay
coherent and the caller sees an empty option array.
- Call free_svc_cred(creds) before kfree(creds) at free_creds:
so the refcounted cr_group_info is released. free_svc_cred()
either NULL-guards each field explicitly (cr_group_info has
an if() check) or delegates to a helper that is NULL-safe
itself (kfree for the string fields, gss_mech_put() which
guards with if(gm) at gss_mech_switch.c:342), so it is safe
to call on a partially decoded svc_cred where only
cr_uid/cr_gid/cr_group_info have been written and everything
else is zero from kzalloc.
- In gssx_dec_linux_creds()'s out_free_groups: path, release
cr_group_info with put_group_info() rather than groups_free()
so the teardown matches free_svc_cred()'s refcount-aware path,
and clear the pointer so a later free_svc_cred() on the same
creds does not release it a second time. |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: fix use-after-free in __rpc_clnt_handle_event and __rpc_clnt_remove_pipedir
Normal client creation goes through rpc_setup_pipedir(), which records
clnt->pipefs_sb, but the mount-event path in __rpc_clnt_handle_event()
calls rpc_setup_pipedir_sb() directly and never refreshes that field.
The umount path also removes the directory without clearing
clnt->pipefs_sb.
After a late pipefs mount or any remount, rpc_clnt_remove_pipedir()
compares the current superblock against a stale pipefs_sb pointer and
skips cleanup, leaving pipefs dentries whose inode private data still
points at a freed rpc_clnt, leading to a potential use-after-free during
subsequent rpc_info_open() or rpc_show_info() calls.
Fix this by properly updating clnt->pipefs_sb upon mount events and
clearing it during unmount or failure paths. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: Reorder rpcrdma_rn_unregister before rdma_destroy_id
svc_rdma_free() caches rdma->sc_cm_id->device before teardown,
then calls rdma_destroy_id(sc_cm_id) which frees the cm_id.
rpcrdma_rn_unregister() follows, but between those two calls
the transport's sc_rn entry is still installed in the device's
rd_xa. A concurrent ib_unregister_device walk can dispatch
svc_rdma_xprt_done() against the now-freed sc_cm_id.
Move rpcrdma_rn_unregister() before rdma_destroy_id() so the
transport's notification entry is removed from the xarray before
the cm_id it references is destroyed.
Also guard the sc_cm_id dereference with a NULL check: the
following patches introduce paths that reach svc_rdma_free()
with sc_cm_id == NULL (listener create failure, ADDR_CHANGE
replacement failure). |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: validate directory-index entry counts when reading metadata
ocfs2_validate_dx_leaf() and ocfs2_validate_dx_root() check the ECC and
signature of an indexed-directory block before it reaches higher-level
callers, but neither validator bounds the ocfs2_dx_entry_list counts
against the capacity of the block that holds them.
ocfs2_dx_dir_search() then walks
for (i = 0; i < le16_to_cpu(entry_list->de_num_used); i++)
dx_entry = &entry_list->de_entries[i];
over de_num_used entries with no bounds check. entry_list is either
dx_leaf->dl_list (from ocfs2_read_dx_leaf) or, for an inline root,
dx_root->dr_entries. A crafted on-disk image can set de_num_used (and
de_count, which is the __counted_by_le() bound of de_entries) to 0xffff
and make the walk read far past the end of the 4KB metadata block, giving
a slab out-of-bounds read reachable from any path lookup, stat() or open()
on an indexed directory once the image is mounted.
Commit 775c17386a6f ("ocfs2: validate dx_root extent list fields during
block read") already bounds dr_list for the non-inline dx_root, but left
the inline dr_entries path and the dx_leaf dl_list unchecked. Add the
same read-time validation for both entry lists: de_count must equal the
capacity of the block (ocfs2_dx_entries_per_leaf()/per_root()) and
de_num_used must not exceed de_count, rejecting corrupted metadata with
-EFSCORRUPTED before ocfs2_dx_dir_search() can walk an out-of-range entry
array.
de_count is always written as exactly the block capacity when a leaf or
inline root is formatted, so the equality check does not reject any valid
image.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: iaa - unmap dst before software fallback on decompress
On a hardware analytics error, decompress retries through the software
fallback, which writes req->dst with the CPU while it is still mapped
DMA_FROM_DEVICE. With SWIOTLB active the later dma_unmap_sg() copies the
stale bounce buffer over req->dst, corrupting the result.
Unmap before the fallback runs. The async path unmaps inline; the sync
path signals the retry with -EAGAIN so iaa_comp_adecompress() runs the
fallback after unmapping. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: fix race between interrupt and resend
After commit f8fce75fedf7 ("fuse: clear intr_entry in fuse_resend and
fuse_remove_pending_req") the WARN_ON(!list_empty(&req->intr_entry)) in
fuse_request_free() still triggers due to the following race:
In request_wait_answer()
if (test_bit(FR_SENT, &req->flags)) -> returns true
In fuse_chan_resend()
clear_bit(FR_SENT, &req->flags)
In request_wait_answer()
queue_interrupt(req)
Fix by:
- move clearing FR_SENT inside fpq->lock
- move setting FR_PENDING inside fiq->lock
- recheck FR_SENT after acquiring fiq->lock in fuse_dev_queue_interrupt() |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: clamp route advmss to TCP_MIN_MSS
tcp_select_initial_window() assumes that callers never pass an MSS
smaller than 1, but route-derived advmss values can violate that
assumption.
A too-small explicit RTAX_ADVMSS is one way to get there, but it is not
the only one. The same divide-by-zero can also be reached through the
"default advmss" path when RTAX_ADVMSS is left at 0 and the effective
advmss is later driven down by route MTU and min_adv_mss.
Introduce a tcp_dst_advmss() helper that clamps route advmss to
TCP_MIN_MSS before TCP consumes it, and use it in the TCP paths that
derive advmss from dst metrics. This keeps the effective MSS from
dropping to zero before tcp_select_initial_window() rounds the receive
window. |
| In the Linux kernel, the following vulnerability has been resolved:
l2tp: fix tunnel and session refcount leak on seq_file release
In pppol2tp_proc_open() and l2tp_dfs_seq_open(), iteration state
(pd->tunnel and pd->session) is kept in seq_file private data to allow
iteration across multiple read() system calls.
However, if userspace closes /proc/net/pppol2tp or /sys/kernel/debug/l2tp/tunnels
before reading to end-of-file (EOF), any tunnel or session reference stored in
pd->tunnel / pd->session is left un-dropped when seq_file private data is freed.
Fix this by dropping any remaining pd->tunnel and pd->session references in
pppol2tp_proc_release() and l2tp_dfs_seq_release() when closing the file. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: cancel SSR work items during PCI shutdown
A reboot can crash the kernel if it overlaps with WLAN firmware crash
recovery (SSR). The crash is a NULL pointer dereference in the MHI teardown
path while freeing DMA-backed MHI contexts.
Simplified trace:
dma_free_attrs
mhi_deinit_dev_ctxt [mhi]
ath11k_pci_power_down [ath11k_pci]
ath11k_pci_shutdown [ath11k_pci]
device_shutdown
kernel_restart
On the host side, SSR is driven by the MHI RDDM callback, which queues
reset_work to perform device recovery. reset_work power-cycles the device
by calling ath11k_hif_power_down() followed by ath11k_hif_power_up(). The
power-down phase deinitializes MHI and frees DMA resources.
Shutdown/reboot runs fully asynchronously with this RDDM-driven SSR
recovery flow. As a result, the shutdown path
(ath11k_pci_shutdown() -> ath11k_pci_power_down()) can race with the SSR
recovery sequence.
Fix this by canceling SSR-related work items during PCI shutdown, marking
the device as unregistering, and serializing the RDDM callback path that
checks and queues reset_work. This ensures that no new SSR recovery work
can be queued once teardown has started, and that any in-flight recovery
work is fully synchronized before device power-down, preventing MHI
teardown and DMA resource freeing from running more than once.
Note: This issue only affects PCI/MHI-based devices. AHB-based ath11k
devices do not queue reset_work in normal SSR flows.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04866.5-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1 |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt: fix head underflow on XDP head-grow
The xdp.py test test_xdp_native_adjst_head_grow_data crashes when run on
a bnxt machine (and also crashes in NIPA).
It seems that the bug is an underflow in bnxt_rx_multi_page_skb, which
builds the skb head:
napi_build_skb(data_ptr - bp->rx_offset, rxr->rx_page_size);
The problem with this expression is that in page mode, rx_offset is:
bp->rx_offset = NET_IP_ALIGN + XDP_PACKET_HEADROOM;
Which evaluates (at least on x86_64) to 258.
The test test_xdp_native_adjst_head_grow_data tests a case where the
head is adjusted by -256.
When this test runs, data_ptr is shifted to frag_start + 2 (where
frag_start = page_address(page) + offset).
Then, bnxt_rx_multi_page_skb is invoked and the napi_build_skb
expression subtracts 258, landing at an address before frag_start. This
could be either the previous fragment or the previous physical page when
the offset is < 256 (e.g. if the fragment started at offset 0).
When the skb is freed, the page pool fragment reference is dropped on
either the wrong page or the wrong frag of the right page. In either
case, the corrupted reference count can lead to the page being
prematurely recycled while still in use. Once (incorrectly) recycled, it
can be handed out again and on driver teardown this would result in a
double free.
The commit under fixes updated this code to handle the case where the
native page size is >= 64k, but it unintentionally broke the head grow
case.
To fix this, add an offset field to struct bnxt_sw_rx_bd, mirroring the
existing offset field in struct bnxt_sw_rx_agg_bd. Populate it on
allocation and preserve it on reuse.
In bnxt_rx_multi_page_skb, use the newly added offset field to compute
the fragment start and pass that to napi_build_skb. Adjust the layout
with skb_reserve.
There are two cases, the non-adjustment case and the adjustment case.
In both cases, the skb is built at page_address(page) + offset to
account for the case where the native page size >= 64K and skb_reserve
is called with data_ptr - (page_address(page) + offset). That
difference equals bp->rx_offset when data_ptr was not moved, or
bp->rx_offset + xdp_adjust when XDP adjusted the head.
Re-running the failing test with this commit applied causes the test to
run successfully to completion.
The other rx_skb_func implementations don't have this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Replace waitqueue and flag with completion
The driver previously used a waitqueue along with an explicit
request_done flag, but without proper barriers around request_done.
An earlier patch by Gui-Dong Han <hanguidong02@gmail.com> attempted
to fix this by adding the missing memory barriers. Rather than
adding the barriers, this patch replaces the waitqueue+flag with
a completion, which is designed for this exact purpose. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix writes_pending and barrier reference leaks on discard failures
raid10_make_request() acquires a writes_pending reference with
md_write_start() before calling raid10_handle_discard(). Several failure
paths in raid10_handle_discard() complete the bio and return without
releasing the corresponding reference, causing md_write_end() to be
skipped.
Call md_write_end() before returning from these failure paths to keep
writes_pending accounting balanced.
Additionally, discard split allocation failures can occur after
wait_barrier() succeeds. Those paths return without calling
allow_barrier(), leaking the associated barrier reference.
Release the barrier before returning from those paths. |
